pass-through terminal for connecting 1 nozzle
material: nickel-plated brass
max. pressure: 120 bar
pipe connector: 1/4” = 6.35 mm (outer diameter)
Fog cooling – air cooling for terraces and pup gardens
The Fog Machine FG150 is able to make you feel comfortable also on extremely hot days by cooling even outdoor areas like terraces, pub gardens and other places and it is also very useful for workshops, green houses and so on. A low energy and water consumption makes the system very economical. The 3- piston pump unit with a special new created motor and a sensorcontrol have made this high pressure misting system with 1000 PSI (70 bar) pressure performance to a sophisticated product which contrasts sharply with standard solutions with respect to energy consumption, water consumption and durability.
Up to 10 °C cooling effect is possible!
Mist coolers cool if they are set correctly, the fineness of the droplets and their distribution are decisive for this.In our set-offer you can find all components which are necessary for operation. You just need a 220V socket and a water connection (with hygienically safe drinking water or filtered water).
Technical data:
Pump: 3-piston high pressure pump
Pump oil: 40 ml (recommended: motor oil 5W-30 for high temperature use). Before starting the system, it has to be filled with oil! The oil is not included with the delivery!!!
Electrical connection: 230 V / 50 Hz
Power consumption: 220 W
Pressure: max. 1000 PSI (70 bar)
Water flow: 1,5 l/min
Noise level under pressure: ca. 53 – 58 db
Water feed pressure: max. 5 bar
Water quality: hygienically safe drinking water or filtered water
Maintenance interval: after 300 operating hours (see instruction manual)
HS-Code: 84248970900
Scope of delivery:
| Detailed configuration | Quantity | |
| Main system | *3-piston pump | |
| * sensor key system | 1 | |
| * 300 hours oil change reminder system | ||
| Conduit system | Very fine water filter (SS304 filter) | 1 |
|
|
Polyether pipe with connector for water tap | 1.5 m |
| Polyether pipe with connector for pressure pump | 1.5 m | |
| Connectors for water filter (already fitted) | 2 | |
| Pressure system (1/4" system) | PA12 pipe (better qualitty than PA 6 & 11) | 5 |
| Top level nozzle (0.2mm) | 20 | |
|
|
Fittings for high-speed assembly (for 1 nozzle) | 19 |
| High-speed assembly end cap | 1 | |
| L-type plug-in coupling | 4 | |
| 0.75m SS pipe (250 bar) | 19 | |
| 0.25m SS pipe (250 bar) | 7 | |
| SS material – pipe clamps | 20 | |
| Machine- & pipe connector | 1 | |
| Other components | Pipe cutter (big size) | 1 |
| Very heavy packing (weight up to 50 Kg) | 1 | |
| Users manual | 1 | |
| Syringe for funnel the oil | 1 | |
| Bearing and O-ring | 1 |
Fog cooling – air cooling for terraces and pup gardens
The Fog Machine FG150 is able to make you feel comfortable also on extremely hot days by cooling even outdoor areas like terraces, pub gardens and other places and it is also very useful for workshops, green houses and so on. A low energy and water consumption makes the system very economical. The 3- piston pump unit with a special new created motor and a sensorcontrol have made this high pressure misting system with 1000 PSI (70 bar) pressure performance to a sophisticated product which contrasts sharply with standard solutions with respect to energy consumption, water consumption and durability.
Up to 10 °C cooling effect is possible!
Mist coolers cool if they are set correctly, the fineness of the droplets and their distribution are decisive for this.In our set-offer you can find all components which are necessary for operation. You just need a 220V socket and a water connection (with hygienically safe drinking water or filtered water).
Technical data:
Pump: 3-piston high pressure pump
Pump oil: 40 ml (recommended: motor oil 5W-30 for high temperature use). Before starting the system, it has to be filled with oil! The oil is not included with the delivery!!!
Electrical connection: 230 V / 50 Hz
Power consumption: 220 W
Pressure: max. 1000 PSI (70 bar)
Water flow: 1,5 l/min
Noise level under pressure: ca. 53 – 58 db
Water feed pressure: max. 5 bar
Water quality: hygienically safe drinking water or filtered water
Maintenance interval: after 300 operating hours (see instruction manual)
HS-Code: 84248970900
Scope of delivery:
| Detailed configuration | Quantity | |
| Main system | *3-piston pump | |
| * sensor key system | 1 | |
| * 300 hours oil change reminder system | ||
| Conduit system | Very fine water filter (SS304 filter) | 1 |
|
|
Polyether pipe with connector for water tap | 1.5 m |
| Polyether pipe with connector for pressure pump | 1.5 m | |
| Connectors for water filter (already fitted) | 2 | |
| Pressure system (1/4" system) | PA12 pipe (better qualitty than PA 6 & 11) | 5 |
| Top level nozzle (0.2mm) | 20 | |
|
|
Fittings for high-speed assembly (for 1 nozzle) | 19 |
| High-speed assembly end cap | 1 | |
| L-type plug-in coupling | 4 | |
| 0.75m SS pipe (250 bar) | 19 | |
| 0.25m SS pipe (250 bar) | 7 | |
| SS material – pipe clamps | 20 | |
| Machine- & pipe connector | 1 | |
| Other components | Pipe cutter (big size) | 1 |
| Very heavy packing (weight up to 50 Kg) | 1 | |
| Users manual | 1 | |
| Syringe for funnel the oil | 1 | |
| Bearing and O-ring | 1 |
Fog cooling – air cooling for terraces and pup gardens
The Fog Machine FG150 is able to make you feel comfortable also on extremely hot days by cooling even outdoor areas like terraces, pub gardens and other places and it is also very useful for workshops, green houses and so on. A low energy and water consumption makes the system very economical. The 3- piston pump unit with a special new created motor and a sensorcontrol have made this high pressure misting system with 1000 PSI (70 bar) pressure performance to a sophisticated product which contrasts sharply with standard solutions with respect to energy consumption, water consumption and durability.
Up to 10 °C cooling effect is possible!
Mist coolers cool if they are set correctly, the fineness of the droplets and their distribution are decisive for this.In our set-offer you can find all components which are necessary for operation. You just need a 220V socket and a water connection (with hygienically safe drinking water or filtered water).
Technical data:
Pump: 3-piston high pressure pump
Pump oil: 40 ml (recommended: motor oil 5W-30 for high temperature use). Before starting the system, it has to be filled with oil! The oil is not included with the delivery!!!
Electrical connection: 230 V / 50 Hz
Power consumption: 220 W
Pressure: max. 1000 PSI (70 bar)
Water flow: 1,5 l/min
Noise level under pressure: ca. 53 – 58 db
Water feed pressure: max. 5 bar
Water quality: hygienically safe drinking water or filtered water
Maintenance interval: after 300 operating hours (see instruction manual)
HS-Code: 84248970900
Scope of delivery:
| Detailed configuration | Quantity | |
| Main system | *3-piston pump | |
| * sensor key system | 1 | |
| * 300 hours oil change reminder system | ||
| Conduit system | Very fine water filter (SS304 filter) | 1 |
|
|
Polyether pipe with connector for water tap | 1.5 m |
| Polyether pipe with connector for pressure pump | 1.5 m | |
| Connectors for water filter (already fitted) | 2 | |
| Pressure system (1/4" system) | PA12 pipe (better qualitty than PA 6 & 11) | 5 |
| Top level nozzle (0.2mm) | 20 | |
|
|
Fittings for high-speed assembly (for 1 nozzle) | 19 |
| High-speed assembly end cap | 1 | |
| L-type plug-in coupling | 4 | |
| 0.75m SS pipe (250 bar) | 19 | |
| 0.25m SS pipe (250 bar) | 7 | |
| SS material – pipe clamps | 20 | |
| Machine- & pipe connector | 1 | |
| Other components | Pipe cutter (big size) | 1 |
| Very heavy packing (weight up to 50 Kg) | 1 | |
| Users manual | 1 | |
| Syringe for funnel the oil | 1 | |
| Bearing and O-ring | 1 |
Fog cooling – air cooling for terraces and pup gardens
The Fog Machine FG150 is able to make you feel comfortable also on extremely hot days by cooling even outdoor areas like terraces, pub gardens and other places and it is also very useful for workshops, green houses and so on. A low energy and water consumption makes the system very economical. The 3- piston pump unit with a special new created motor and a sensorcontrol have made this high pressure misting system with 1000 PSI (70 bar) pressure performance to a sophisticated product which contrasts sharply with standard solutions with respect to energy consumption, water consumption and durability.
Up to 10 °C cooling effect is possible!
Mist coolers cool if they are set correctly, the fineness of the droplets and their distribution are decisive for this.In our set-offer you can find all components which are necessary for operation. You just need a 220V socket and a water connection (with hygienically safe drinking water or filtered water).
Technical data:
Pump: 3-piston high pressure pump
Pump oil: 40 ml (recommended: motor oil 5W-30 for high temperature use). Before starting the system, it has to be filled with oil! The oil is not included with the delivery!!!
Electrical connection: 230 V / 50 Hz
Power consumption: 220 W
Pressure: max. 1000 PSI (70 bar)
Water flow: 1,5 l/min
Noise level under pressure: ca. 53 – 58 db
Water feed pressure: max. 5 bar
Water quality: hygienically safe drinking water or filtered water
Maintenance interval: after 300 operating hours (see instruction manual)
HS-Code: 84248970900
Scope of delivery:
| Detailed configuration | Quantity | |
| Main system | *3-piston pump | |
| * sensor key system | 1 | |
| * 300 hours oil change reminder system | ||
| Conduit system | Very fine water filter (SS304 filter) | 1 |
|
|
Polyether pipe with connector for water tap | 1.5 m |
| Polyether pipe with connector for pressure pump | 1.5 m | |
| Connectors for water filter (already fitted) | 2 | |
| Pressure system (1/4" system) | PA12 pipe (better qualitty than PA 6 & 11) | 5 |
| Top level nozzle (0.2mm) | 20 | |
|
|
Fittings for high-speed assembly (for 1 nozzle) | 19 |
| High-speed assembly end cap | 1 | |
| L-type plug-in coupling | 4 | |
| 0.75m SS pipe (250 bar) | 19 | |
| 0.25m SS pipe (250 bar) | 7 | |
| SS material – pipe clamps | 20 | |
| Machine- & pipe connector | 1 | |
| Other components | Pipe cutter (big size) | 1 |
| Very heavy packing (weight up to 50 Kg) | 1 | |
| Users manual | 1 | |
| Syringe for funnel the oil | 1 | |
| Bearing and O-ring | 1 |
With the Fog Machine ZDS-DC12V it is possible to make even extremely hot days bearable and with very low energy and water consumption to achieve a noticeable cooling for the outside area in front of mobile homes, terraces, balconies!
The ZDS-DC12V pump unit has made this high-pressure fogging unit with 70 bar (1000 PSI) pressure output a mature product that stands out from standard solutions in terms of durability, energy requirements and water consumption.
Cooling effects of up to 10 °C are possible!
All you need on site is a 230 V mains socket and a water connection (with hygienically harmless or filtered fresh water).
";s:20:"products_description";s:2887:"With the Fog Machine ZDS-DC12V it is possible to make even extremely hot days bearable and with very low energy and water consumption to achieve a noticeable cooling for the outside area in front of mobile homes, balconies, terraces!
The ZDS-DC12V pump unit has made this high-pressure fogging unit with 70 bar (1000 PSI) pressure output a mature product that stands out from standard solutions in terms of durability, energy requirements and water consumption.
Cooling effects of up to 10 °C are possible!
Fog cooling systems cool if they are set correctly without you getting wet. The fineness of the droplets and their distribution is decisive. This also results in low water consumption. Our range of sets includes all components required for operation.
All you need on site is a 230 V mains socket and a water connection (with hygienically harmless or filtered fresh water).
Technical data:
ZDS-DC12V
Pump Working pressure: 70kg/cm2(1000psi)
Flow rate: 0.2 l/minM
Thermistor: 85 degrees C
Motor Permanent magnet DC brush motor, completely closed
Service life approx. 2000 h (pump head)
Weight: 0.9 kg
No-load Current: 0.573A W: 7W RPM: 2470RPM
Full load current: 2.26A W: 16W
Output speed : 1980 RPM Kg-cm : 0.8
Customs tariff number: 84248970900
Scope of delivery:
- Pump set ZDS-DC12V
- Controller set with power supply and remote control only for Start/Stop function >>> see operating instructions
- 5 high-pressure mist nozzles 0.15 mm
- 4 high-pressure hose connectors for 1 mist nozzle
- End caps with connection for high-pressure hose and 1 mist nozzle
Attention: High pressure hose must be ordered additionally under accessories according to your installation method! Not included in the scope of delivery!
Water filter must be ordered additionally under accessories according to your water quality! Not included in the scope of delivery! Only use hygienically harmless or filtered fresh water !
generates an ultra-fine hovering fog with a pressure of 50 – 70 bar for air humidification and cooling. It is possible to open the nozzle completely for cleaning it easily.
Technical data:
nozzle bore: 0.10 mm
nozzle body: nickel-plated brass
nozzle head: stainless steel SS304
max. pressure: 120 bar
stainless steel filter included
length: 41 mm
(also called atomizer nozzle or misting nozzle) atomises liquids under pressure into finest droplets having a large specific surface. These fine droplets evaporate in the air and increase the humidity. A pump pressure of 50 – 70 bar is optimal to generate the ultra-fine floating droplets. For several applications and humidity different nozzle sizes are available. Please consider that the quality of the used water is important for a proper function and the durability of the nozzles.
Technical data:
nozzle bore: 0.10 mm
nozzle body: nickel-plated brass
nozzle head: stainless steel SS304
max. pressure: 120 bar
stainless steel filter included
length: 41 mm
| Flow rate in litres per hour | ||||||||
| referring to different pressure values | ||||||||
| casing material |
nozzle outlet material |
nozzle bore mm |
droplet size µm |
10 bar / 150 psi l/h |
45 bar / 650 psi l/h |
70 bar / 1000 psi l/h |
83 bar / 1200 psi l/h |
spray angle (degree) |
| nickel-plated brass | SS304 | 0.1 | 3 – 8 | -- | 2.7 | 3.2 | 4.5 | 50-65 |
| 0.15 | -- | 3.2 | 3.5 | 4.8 | 60-70 | |||
| 0.2 | 1.9 | 4.0 | 4.9 | 5.6 | 65-80 | |||
| 0.3 | 2.6 | 5.3 | 6.6 | 7.4 | 80-83 | |||
| 0.4 | 3.5 | 7.3 | 9.1 | 10.0 | 80-85 | |||
| 0.5 | 4.8 | 10.0 | 12.0 | 13.0 | 83-90 | |||
generates an ultra-fine hovering fog with a pressure of 50 – 70 bar for air humidification and cooling. It is possible to open the nozzle completely for cleaning it easily.
Technical data:
nozzle bore: 0.15 mm
nozzle body: nickel-plated brass
nozzle head: stainless steel SS304
max. pressure: 120 bar
stainless steel filter included
length: 41 mm
(also called atomizer nozzle or misting nozzle) atomises liquids under pressure into finest droplets having a large specific surface. These fine droplets evaporate in the air and increase the humidity. A pump pressure of 50 – 70 bar is optimal to generate the ultra-fine floating droplets. For several applications and humidity different nozzle sizes are available. Please consider that the quality of the used water is important for a proper function and the durability of the nozzles.
Technical data:
nozzle bore: 0.15 mm
nozzle body: nickel-plated brass
nozzle head: stainless steel SS304
max. pressure: 120 bar
stainless steel filter included
length: 41 mm
| Flow rate in litres per hour | ||||||||
| referring to different pressure values | ||||||||
| casing material |
nozzle outlet material |
nozzle bore mm |
droplet size µm |
10 bar / 150 psi l/h |
45 bar / 650 psi l/h |
70 bar / 1000 psi l/h |
83 bar / 1200 psi l/h |
spray angle (degree) |
| nickel-plated brass | SS304 | 0.1 | 3 – 8 | -- | 2.7 | 3.2 | 4.5 | 50-65 |
| 0.15 | -- | 3.2 | 3.5 | 4.8 | 60-70 | |||
| 0.2 | 1.9 | 4.0 | 4.9 | 5.6 | 65-80 | |||
| 0.3 | 2.6 | 5.3 | 6.6 | 7.4 | 80-83 | |||
| 0.4 | 3.5 | 7.3 | 9.1 | 10.0 | 80-85 | |||
| 0.5 | 4.8 | 10.0 | 12.0 | 13.0 | 83-90 | |||
generates an ultra-fine hovering fog with a pressure of 50 – 70 bar for air humidification and cooling. It is possible to open the nozzle completely for cleaning it easily.
Technical data:
nozzle bore: 0.20 mm
nozzle body: nickel-plated brass
nozzle head: stainless steel SS304
max. pressure: 120 bar
stainless steel filter included
length: 41 mm
(also called atomizer nozzle or misting nozzle) atomises liquids under pressure into finest droplets having a large specific surface. These fine droplets evaporate in the air and increase the humidity. A pump pressure of 50 – 70 bar is optimal to generate the ultra-fine floating droplets. For several applications and humidity different nozzle sizes are available. Please consider that the quality of the used water is important for a proper function and the durability of the nozzles.
Technical data:
nozzle bore: 0.20 mm
nozzle body: nickel-plated brass
nozzle head: stainless steel SS304
max. pressure: 120 bar
stainless steel filter included
length: 41 mm
| Flow rate in litres per hour | ||||||||
| referring to different pressure values | ||||||||
| casing material |
nozzle outlet material |
nozzle bore mm |
droplet size µm |
10 bar / 150 psi l/h |
45 bar / 650 psi l/h |
70 bar / 1000 psi l/h |
83 bar / 1200 psi l/h |
spray angle (degree) |
| nickel-plated brass | SS304 | 0.1 | 3 – 8 | -- | 2.7 | 3.2 | 4.5 | 50-65 |
| 0.15 | -- | 3.2 | 3.5 | 4.8 | 60-70 | |||
| 0.2 | 1.9 | 4.0 | 4.9 | 5.6 | 65-80 | |||
| 0.3 | 2.6 | 5.3 | 6.6 | 7.4 | 80-83 | |||
| 0.4 | 3.5 | 7.3 | 9.1 | 10.0 | 80-85 | |||
| 0.5 | 4.8 | 10.0 | 12.0 | 13.0 | 83-90 | |||
this high pressure pipe is made from nylon PA12. That material is used for installations in high pressure misting systems up to 100 bar. The pipe diameter of just 1/4” (6,35 mm) makes the material very flexible and allows a quick and optimal installation. Several pressure fittings by JOSTechnik are available to connect the high pressure pipes.
Product properties:
material: nylon PA12 (ageing resistant, twice the lifespan of PA6 or PA11)
temperature range: between -40°C and +120°C
max. pressure: 100 bar
color: black
diameter: 1/4” = 6,35 mm (outer diameter)
price per meter
pass-through nozzle support (for 1 nozzle) from nickel-plated brass with quick-fit-system for high pressure nozzle systems with 1/4” (6,35 mm) pressure pipe.
- easy and quick assembly
- more than 50 % reduced mounting effort in relation to stainless steel pipes
- simply to extend
- flexible placement
- disposable product
Technical data:
pass-through terminal for connecting 1 nozzle
material: nickel-plated brass
max. pressure: 120 bar
pipe connector: 1/4” = 6.35 mm (outer diameter)
";s:11:"products_id";i:333;s:14:"products_price";s:6:"4.5378";s:25:"products_discount_allowed";d:15;s:12:"products_vpe";i:0;s:19:"products_vpe_status";i:0;s:18:"products_vpe_value";s:6:"0.0000";}i:12;a:21:{s:14:"products_fsk18";i:0;s:23:"products_date_available";s:19:"0000-00-00 00:00:00";s:21:"products_shippingtime";i:8;s:14:"products_model";s:3:"334";s:15:"products_master";i:0;s:22:"products_master_status";i:0;s:12:"products_ean";s:0:"";s:13:"products_name";s:34:"Nozzle support 1/4'' for 2 nozzles";s:19:"products_extra_text";s:0:"";s:17:"products_quantity";i:182;s:16:"manufacturers_id";i:10;s:14:"products_image";s:9:"334_0.jpg";s:15:"products_weight";s:5:"0.031";s:26:"products_short_description";s:382:"pass-through nozzle support (for 2 nozzles) from nickel-plated brass with quick-fit-system for high pressure nozzle systems with 1/4” (6,35 mm) pressure pipe.
pass-through nozzle support (for 2 nozzles) from nickel-plated brass with quick-fit-system for high pressure nozzle systems with 1/4” (6,35 mm) pressure pipe.
- easy and quick assembly
- more than 50 % reduced mounting effort in relation to stainless steel pipes
- simply to extend
- flexible placement
- disposable product
Technical data:
pass-through terminal for connecting 2 nozzles
material: nickel-plated brass
max. pressure: 120 bar
pipe connector: 1/4” = 6.35 mm (outer diameter)
End fittings are used to terminate the pressure pipes in the high pressure misting system.
Quick and tool-free assembly.
Technical data:
";s:11:"products_id";i:337;s:14:"products_price";s:6:"3.2773";s:25:"products_discount_allowed";d:15;s:12:"products_vpe";i:0;s:19:"products_vpe_status";i:0;s:18:"products_vpe_value";s:6:"0.0000";}i:14;a:21:{s:14:"products_fsk18";i:0;s:23:"products_date_available";s:19:"0000-00-00 00:00:00";s:21:"products_shippingtime";i:8;s:14:"products_model";s:0:"";s:15:"products_master";i:0;s:22:"products_master_status";i:0;s:12:"products_ean";s:0:"";s:13:"products_name";s:49:"End fitting 1/4 " with 1 nozzle support (lateral)";s:19:"products_extra_text";s:0:"";s:17:"products_quantity";i:48;s:16:"manufacturers_id";i:10;s:14:"products_image";s:9:"335_0.jpg";s:15:"products_weight";s:5:"0.031";s:26:"products_short_description";s:407:"end fitting – nozzle support for 1 nozzle (lateral assembling), nickel-plated brass with quick-fit-system, for high pressure nozzle system with 1/4” (6,35 mm) pressure pipe.
Technical data:
end fitting with 1 nozzle support (lateral)
material: nickel-plated brass
max. pressure: 120 bar
pipe connector: 1/4” = 6.35 mm (outer diameter)
end fitting – nozzle support for 1 nozzle (lateral assembling), nickel-plated brass with quick-fit-system, for high pressure nozzle system with 1/4” (6,35 mm) pressure pipe. End fittings with nozzle support are used to terminate the end of a pipe in the high pressure misting system. This high pressure nozzle support is arranged in a right angle to the pipe connection.
Easy and quick assembly without tools is given by a quick-fit-system.
Technical data:
end fitting with 1 nozzle support (lateral)
material: nickel-plated brass
max. pressure: 120 bar
pipe connector: 1/4” = 6.35 mm (outer diameter)
end fitting – nozzle support for 2 nozzles (lateral assembling), nickel-plated brass with quick-fit-system, for high pressure nozzle system with 1/4” (6,35 mm) pressure pipe. End fittings with nozzle support are used to terminate the end of a pipe in the high pressure misting system. This high pressure nozzle support is arranged in a right angle to the pipe connection.
Easy and quick assembly without tools is given by a quick-fit-system.
Technical data:
end fitting with 2 nozzle supports (lateral)
material: nickel-plated brass
max. pressure: 120 bar
pipe connector: 1/4” = 6.35 mm (outer diameter)
cross fitting, nickel-plated brass with quick-fit-system, for high pressure nozzle system with 1/4” (6,35 mm) pressure pipe. Cross fittings are used to joint the pipes in the high pressure misting system.
Easy and quick assembly without tools is given by a quick-fit-system.
Technical data:
cross-fitting
material: nickel-plated brass
max. pressure: 120 bar
pipe connector: 1/4” = 6.35 mm (outer diameter)
L-shaped fitting, nickel-plated brass with quick-fit-system, for high pressure nozzle system with 1/4” (6,35 mm) pressure pipe. L-shaped fittings are used to joint the pipes in the high pressure misting system.
Easy and quick assembly without tools is given by a quick-fit-system.
Technical data:
fitting (L-shaped)
material: nickel-plated brass
max. pressure: 120 bar
pipe connector: 1/4” = 6.35 mm (outer diameter)
T-shaped fitting, nickel-plated brass with quick-fit-system, for high pressure nozzle system with 1/4” (6,35 mm) pressure pipe. T-shaped fittings are used to joint the pipes in the high pressure misting system.
Easy and quick assembly without tools is given by a quick-fit-system.
Technical data:
fitting (T-shaped)
material: nickel-plated brass
max. pressure: 120 bar
pipe connector: 1/4” = 6.35 mm (outer diameter)